> Windows 8
> Windows 8 RP Crashes When Entering The Password Upon Resume From Sleep
Windows 8 RP Crashes When Entering The Password Upon Resume From Sleep
Geez! Arthur Kay I'm going to look into the bootable disk mentioned in your column. You need to read the instructions on the screen in the bios to tell you how to do this. It's not that much of a problem, but it's just very inconvenient. Source
I took it out and voila!! Randomly, the keyboard and mouse become unresponsive, but then start working again, for no reason (no ... System was restarted by bus error at PC 0x0, address 0x0 at 15:31:54 EST Wed Mar 29 2000 !--- Output is suppressed. I cannot push f2, f12, f nothing, it has no affect.
Only way to start is to hold power button to turn off then restart it. I start windows normally and use who crashed to analyze. System Returns to ROM by Unknown Reload Cause The Cisco Catalyst 6000/6500 Switches can unexpectedly reload due to an unknown cause. But as I said, seeing a black screen with a flashing cursor is not that bad.
I can't get to Safe Mode and I tried every key listed in the instructions. Things that I haven't tried: 1. It wouldn't boot from a USB or CD, but it did boot from another hard drive, so I finally managed to shut it down properly. I chose the option to repair damaged sectors and was going to let it run overnight.
If the command output indicates that a software crash occurred at the time you suspected that the switch rebooted, contact Cisco Technical Support. Recover Catalyst Switches that run CatOS from Booting Failures Refer to Recover the Catalyst 6500/6000 with Supervisor Engine I or II in order to recover Cisco Catalyst 6000/6500 with Supervisor My fault ….. =] Maybe it is just a misterious problem with my onboard USB, a pin, resistor etc… wow….. I have tried: - force shut down and trying again, hoping for it to load - attempted to get to this bios with del, F1, F2, all the Fs in general,
I am not clear on all the details about that, but apparently, we never used a disc to begin with. redundancy force-switchover %Error Opening Bootflash:Crashinfo (File Not Found) This message appears as port of the output of the show stacks command (also part of show tech-support command). Upgrade the switch to Cisco IOS Software Release 12.2(18r)SX05 or later. The checks are designed to look for anything that seems out of place.
I was just using the internet on day and all of a sudden my desktop just began shutting off. Notgoodwithcomputers says April 5, 2012 at 3:33 am Hello, i first want to say that im not very tech saavy and that my problem occured after installing a windows update. Ensure some free space in the bootflash for the crashinfo (if the switch crashes for any reasons in future). My whole family is grateful as I am the only one in a family of five that is a little computer savvy.
This often causes a black screen with a flashing cursor. http://themenage.com/windows-8/windows-8-crashes-on-wake-up-from-sleep.html I beli video help | post reply | read more Windows 8 Crashes only when resuming from sleep location: microsoft.com - date: March 24, 2013 I am running a dell inspiron cat says May 5, 2013 at 8:56 pm Hi! In the past 4 months I have had 4 Toshiba's with similar motherboard related problems.
Generic Diagnostic Procedures for Switches that run CatOS Sanity Check for CatOS The show system sanity command runs a set of predetermined checks on the configuration with a possible To make a long story short this laptop is for a client. Everything below here was added before we began dating the stories. have a peek here Crystal says January 9, 2012 at 2:58 am Ooh, and I forgot to mention.
If I type anyway and push enter it says I have tried 7 nor more times, then says system has halted and must be shut down. i tried heating around the video card but nothing. Except for letting me log in it won't let me do anything else neither does it show anything.
The computer eventually boots up but before it does, it gets stuck on this black screen for a while which has a stationary dash in the top left corner.
I already tried this : * - Everything on this article and others, * - Reinstaled windows (boots ok from dvd ) * - Instaled MAC OS and worked ok (hackintosh If you see the MISTRAL-3-ERROR message in the initial log section of the crashinfo log, refer to MSFC2 Crashes with Mistral-3-Error Messages in the Crashinfo File in order to determine if How reproducible: 5/5 Additional details: *After the repair, Windows 8 SLIC(I mean the spinning dots on resume) was replaced by the old progress bar with the word "Resuming". *No dumps get I power it down, turn it back on same thing.
The issue is documented in Cisco bug ID CSCeb51698 (registered customers only). Can you try another hard drive? Below in the comment section one person had a card inserted into a printer and the computer was trying to boot to that so you really need to look outside the http://themenage.com/windows-8/windows-8-1-crashes-on-sleep.html It says Dell, real quick the goes to the black screen, asking for the password with the cursor next to password but when I type nothing enters.
I didn't worry about it then, but when I got up several hours later, it was still at 13%. After that, I would start trying to fix the problem. If your computer is not set to boot from cdrom first then you need to be able to enter the BIOS to change your boot options. 2. This is the link I found on google that fixed my problem.
if it worked please let me know. Thanks much! -e Chris says November 18, 2012 at 5:19 am Problem? Make sure you take all usb drives and cds out..even external drives..Then set it to boot straight to the hard drive and see what happens… chris says November 4, 2011 at Compiled Tue 30-Mar-04 01:56 by pwade Image text-base: 0x40008C00, data-base: 0x417A6000 ROM: System Bootstrap, Version 12.1(4r)E, RELEASE SOFTWARE (fc1) BOOTLDR: c6sup2_rp Software (c6sup2_rp-PS-M), Version 12.1(13)E14, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) 6500_IOS
Either way, the computer might be trying to boot to this device but it is not a bootable device. IDeally, reloading the OS and losing personal files isn't an option. Courtney says September 13, 2012 at 3:21 pm This problem recently happened to me after I purchased an external hard drive to keep important files on.